Super Duty Dana 60 Axle

The Super Duty Dana 60 is a front axle used commonly in one ton axle conversions on many different Jeep models including the Jeep JK, Jeep JL, Jeep YJ, Jeep TJ and more.  You will also see fabricators using the SD60 in tube buggy builds.  The Super Duty Dana 60 varies a little with different year models.  It is important that you know what year model truck your Super Duty Dana 60 front axle assembly came from. Motobilt offers diff covers for the SD60 along with axle trusses. 

Super Duty Dana 60 Axle

This handy drilling guide is used to mark the hole centers when converting the wheel stub bolt pattern on a Ford Super Duty front axle wheel hubs from 8 bolt on 170mm to 8 bolt on 6.5” bolt circle diameter. Simply place the drilling guide over the stock wheel studs,...
The Motobilt Dana 60 Ford Super Duty diff cover is a heavy duty high clearance design. The diff cover ring is made out of 3/8 inch thick steel plate that is laser cut in house at Motobilt. Next a 1/4 inch thick laser cut plate is cnc formed and welded...
The Motobilt Ford Super Duty Dana 60 lower control arm mounts are just the ticket for that custom suspension setup. This heavy duty 1/4 inch steel brackets are laser cut and cnc formed at the Motobilt headquarters. The will allow you to mount a rod end, flex joint, or other...
The Super Duty Dana 60 inner C coil over shock bracket set is manufactured from laser cut and formed 1/4" steel plate. The inner C shock mounts are designed for 2.0 coil over shocks. The shock mounts fit the 2005+ Dana 60 Super Duty Axle inner C.. Simply bolt on to...
At Motobilt, our heritage began with Builder Parts. This kit evolved over 2 years of development & shows our attention to all of the little details, even in a Builder Kit.The Motobilt High Steering Brackets for Super Duty 60 Axles is a premium Builder kit that solves the issue of...
The Motobilt adjustable track bar bracket is built to take the any abuse you can dish out. This bracket is laser cut from 1/4 inch thick steel plate and CNC formed. The bracket consists of 3 pieces that will need to be welded for install. The brackets utilize 3 different...
The Motobilt Ford Super Duty Dana 60 axle truss is laser cut and bent out of 3/8 inch high strength steel for the main structure. This kit was designed specifically for the 2005 and up Ford F-250 and F350 Dana 60 front axles. The truss spans the length of the...
The Jeep JK 1 ton axle swap kit allows you to use a 2005 and up Ford Super Duty Dana 60 front axle and install it into a Jeep Wrangler JK. It consists of a truss, upper link mounts, lower link mounts, coil spring buckets, adjustable track bar mount for...
The popularity of the Super Duty Dana 60 for off-road buggies and Jeeps is on the rise for its relative low cost and ease to source.  On some builds the ABS sensors in the front unit bearings are not required.  Removing the sensor and adding this aluminum block off plate...
The Ford Super Duty Dana 60 truss from Motobilt will greatly increase the strength of your front axle. The main structure of this axle truss is laser cut and cnc bent from 3/8 inch thick steel plate. Supporting the main truss are 3/8 inch and 3/16 inch structural bracing. The...
If you can weld and want to build your own diff cover, purchase the Dana 60 Super Duty DIY DIFF Cover. Motobilt DIY Diff Covers are the same as our fully-welded diff covers, but sold as a kit including the pre-formed pieces and hardware you will need to complete the...
This handy drilling guide is used to mark the hole centers when converting the wheel stub bolt pattern on a Chevy Dana 60 front axle wheel hubs from 8 bolt on 6.5” to 8 bolt on 170mm bolt circle diameter. Simply place the drilling guide over the stock wheel studs,...
Spinner