Installing aftermarket suspension seats in a Jeep JK or JKU can create problems with seating height, legroom, and interior clearance. Many suspension seats sit taller than factory seats, and adding mounting brackets and sliders can push the seating position even higher. This becomes especially noticeable in Jeeps equipped with aftermarket roll cages, where headroom and proper driver positioning are important. The Motobilt MB2246 Adjustable Front Seat Mounts give builders control over both seat height and fore/aft positioning when installing aftermarket suspension seats.
Designed for 2012–2018 Jeep Wrangler JK and JKU models, the MB2246 includes driver and passenger seat mounts, seat sliders, and two sets of interchangeable seat risers. With no risers installed, the mounting system positions the seat up to 2.25" lower than the factory mounting height. Builders can install the included 1.25" or 2" risers to raise the seat from its lowest mounting position, allowing them to dial in seating height based on driver preference, headroom, and interior clearance. This gives builders three mounting height configurations without having to fabricate additional spacers or brackets.
Each seat mount features three mounting positions for the included seat slider. The center position maintains the factory fore/aft mounting location, while the forward position moves the slider 3/4" forward and the rear position moves it 3/4" backward for additional legroom. The included sliders provide normal seat adjustment after the mounting position has been selected.
The MB2246 is designed for aftermarket suspension seats with vertical mounting tabs underneath the seat, including PRP-style seats using an 18" front-to-rear mounting hole spacing and 14" inside mounting width. Other aftermarket seat manufacturers may also be compatible when their mounting tabs match these dimensions.
Constructed from A36 steel, the brackets also feature separate accent panels positioned behind the Motobilt M logos. These panels can be painted or powder coated in a contrasting color to customize the appearance of the seat mounts.
Designed and manufactured by Motobilt in Ozark, Alabama, the MB2246 provides a practical mounting system for builders upgrading the seats and interior layout of their Jeep JK or JKU.
Important Information
-
Fits 2012–2018 Jeep Wrangler JK 2-door
-
Fits 2012–2018 Jeep Wrangler JKU 4-door
-
Sold as a pair, driver and passenger seat mounts included
-
Designed for aftermarket suspension-style seats with vertical mounting tabs
-
Compatible with PRP-style suspension seats using the specified mounting dimensions
-
Requires 18" front-to-rear mounting hole spacing
-
Requires 14" inside width between the vertical mounting tabs
-
Other aftermarket seat brands may fit when their mounting dimensions and tab configuration match
-
Does not work with factory Jeep JK/JKU seats
-
Does not work with factory Jeep JK/JKU seat sliders
-
Includes aftermarket seat sliders for both front seats
-
Includes removable seat risers
-
Retains factory seat mounting height when using the supplied risers
-
Allows up to 2 1/4" lower seat mounting position with risers removed
-
Three fore/aft seat slider mounting positions
-
Center position maintains the factory fore/aft mounting location
-
Forward mounting position moves the slider 3/4" forward
-
Rear mounting position moves the slider 3/4" rearward
-
Separate Motobilt M logo accent panels can be finished in a contrasting color
-
Constructed from A36 steel
-
Includes 5/16"-18 x 1" Grade 5 zinc-plated carriage bolt fasteners
-
Made in the USA
Product Specifications
Part Number: MB2246
Product Type: Adjustable Front Suspension Seat Mount Kit
Vehicle Fitment:
2012–2018 Jeep Wrangler JK 2-door
2012–2018 Jeep Wrangler JKU 4-door
Application: Aftermarket front suspension seat installation
Material: A36 Steel
Seat Compatibility: Aftermarket suspension seats with compatible vertical mounting tabs
Seat Mounting Hole Spacing: 18" front to rear
Seat Mounting Width: 14" inside width between vertical mounting tabs
Factory Seat Compatibility: Not compatible
Factory Seat Slider Compatibility: Not compatible
Seat Sliders: Included for driver and passenger seats
Seat Risers: Included, removable
Seat Height Adjustment: Factory mounting height with risers installed, or up to 2 1/4" lower with risers removed
Fore/Aft Slider Mounting Positions: Three
Forward Mounting Adjustment: 3/4"
Rearward Mounting Adjustment: 3/4"
Accent Panels: Separate panels positioned behind the Motobilt M logos for custom finishing
Fastener Specification: 5/16"-18 x 1" Grade 5 zinc-plated carriage bolts
Quantity: Pair, driver and passenger side
Dimensions (H/W/D): 15" x 16" x 26"
Weight: 49.1 lbs
Manufactured: Made in the USA
Related Motobilt Product:
Front Seat Mounts for Jeep JLU
Installation Notes
The MB2246 replaces the factory front seat mounting arrangement when installing compatible aftermarket suspension seats in a 2012–2018 Jeep Wrangler JK or JKU.
Seat Compatibility and Mounting Dimensions
Before installation, verify that the aftermarket seats use vertical mounting tabs underneath the seat. The required mounting configuration is 18" between the front and rear mounting holes and 14" inside width between the mounting tabs.
These dimensions are commonly associated with PRP-style suspension seat mounting arrangements. Other aftermarket seats may work if their vertical mounting tabs match the required dimensions. Seats with different mounting patterns or flat-bottom mounting arrangements may require a different mounting system.
Factory Jeep JK/JKU seats and factory seat sliders are not compatible with MB2246.
Seat Height Adjustment
The supplied seat risers provide two mounting height configurations.
Install the risers to retain the factory seat mounting height. Remove the risers to lower the seat mounting position up to 2 1/4".
Actual occupant seating height depends on the design and thickness of the aftermarket suspension seat.
Fore/Aft Seat Position Adjustment
Each bracket includes three mounting positions for the supplied seat slider.
The center mounting position maintains the factory fore/aft slider mounting location. The forward mounting position moves the slider 3/4" toward the front of the Jeep. The rear mounting position moves the slider 3/4" toward the rear of the Jeep, providing additional legroom.
These mounting positions establish the location of the seat slider assembly. The included sliders provide additional adjustment during normal use.
Customizable Logo Accent Panels
The Motobilt M logo accent panels are separate components that can be finished independently from the main seat brackets.
Builders can paint or powder coat the panels in a contrasting color to highlight the Motobilt M logo and coordinate with the Jeep's interior, cage, or other fabricated components.
Finish the accent panels separately before final assembly when using contrasting colors.
Final Installation Checks
Test fit both seats before final assembly. Verify steering wheel clearance, center console clearance, door clearance, roll cage clearance, and full seat slider travel.
Confirm that all seat mounting hardware is installed correctly and securely tightened. Any vehicle-specific seat belt, buckle, or electrical system requirements must be addressed as part of the installation.
Frequently Asked Questions
Will the MB2246 seat mounts work with factory Jeep JK or JKU seats?
No. The MB2246 is specifically designed for aftermarket suspension seats with vertical mounting tabs underneath the seat. Factory Jeep JK/JKU seats and factory seat sliders are not compatible. The kit includes its own seat sliders for both the driver and passenger seats.
What aftermarket suspension seats fit the MB2246 seat mounts?
The MB2246 is designed around PRP-style suspension seats with vertical mounting tabs. The required mounting dimensions are 18" between the front and rear mounting holes and 14" inside width between the mounting tabs. Other manufacturers may also be compatible if their seats use the same mounting dimensions and vertical tab arrangement. Builders should verify these measurements before ordering.
How much lower can I mount my seats with MB2246?
Removing the included seat risers allows the mounting position to be lowered up to 2 1/4" compared with the configuration using the risers. Keeping the risers installed allows the factory seat mounting height to be retained. Actual headroom and occupant seating height depend on the aftermarket seat being installed.
Can I move the seat farther back for more legroom?
Yes. The MB2246 provides three seat slider mounting positions. The rear mounting position moves the slider 3/4" farther back than the center position. The forward position moves it 3/4" forward. The included seat sliders provide additional fore/aft adjustment after installation.
Can I customize the color of the Motobilt M logo on the seat brackets?
Yes. The MB2246 features separate accent panels positioned behind the Motobilt M logos. These panels can be painted or powder coated in a contrasting color before assembly, allowing the logo to stand out and match the interior or other components in the Jeep.